How to Put a Car on 4 Jack Stands Safely and Securely: Step-by-Step Guide

Putting a car up on 4 jack stands is an essential skill for any DIY mechanic. Whether you need to work on the brakes, suspension, or some other part of the vehicle, having the car elevated and supported on 4 jack stands means you have room to work and that it’s safe to do so. But if you’ve never done it before, the process can seem daunting.

In this blog post, we’ll show you step-by-step how to put a car on 4 jack stands, so you can work on your vehicle with confidence. So put on your work clothes, get your tools ready, and let’s get started!

What You Will Need

Putting a car on four jack stands is quite an intricate task that requires the right tools and equipment, as well as safety precautions to avoid accidents. Before starting, it’s essential to ensure that you have the correct jack stands and a reliable hydraulic jack that can lift your car safely. Make sure you choose jack stands that can support your vehicle’s weight and have a secure locking system to prevent them from collapsing.

In addition to these tools, you may also need a wheel chock to prevent the car from moving and a torque wrench to tighten bolts and lug nuts. Finally, always work on a flat, level surface and wear the appropriate safety gear, such as gloves and goggles, before proceeding. With these tools and precautions in place, you can safely and successfully put your car on four jack stands.

4 Jack Stands

When it comes to car maintenance, it’s important to have the right equipment to get the job done safely. If you’re planning on working underneath your car, you’ll need a set of four jack stands to ensure your vehicle is securely lifted off the ground. Jack stands are designed to support the weight of your car while you work on it, and they work in conjunction with a floor jack to lift your car into the air.

To use jack stands, you’ll first need to properly jack up your car using a floor jack, then place the stands under the car at the designated jacking points. It’s essential to use four jack stands instead of just two to ensure even weight distribution and prevent any tipping. When choosing jack stands, look for ones with a weight capacity that exceeds the weight of your vehicle.

Investing in quality jack stands is an important step in staying safe while working on your car, so be sure to do your research and choose a reliable set.

how to put a car on 4 jack stands

A Hydraulic Floor Jack

If you’re looking to lift heavy vehicles or equipment, a hydraulic floor jack is your best bet. But what do you need besides the jack itself? First and foremost, you’ll need a stable surface to place the jack on, such as a concrete or asphalt floor. Next, ensure you have enough space around the vehicle to move it after lifting.

You’ll also need a good quality set of jack stands to help support the vehicle after lifting, preventing it from toppling over. Finally, it’s helpful to have a wheel chock to stop the car from rolling away when lifted. While a hydraulic floor jack may seem like a simple tool, using it correctly and safely requires a few essential accessories.

Make sure you have everything you need before attempting to lift any heavy equipment or vehicles.

Wheel Chocks

When it comes to using wheel chocks, there are a few items that you will need to ensure a safe and proper application. Firstly, you will need the wheel chocks themselves. These are typically made of durable materials such as rubber or hard plastic and are designed to prevent vehicles from rolling when parked or positioned on an incline.

It’s important to purchase chocks that are the right size for your vehicle’s tires and weight to ensure they can provide the necessary stability. Additionally, you will need a flat and stable surface to place the chocks on. Make sure the surface is clear of debris and any obstacles that could interfere with the functionality of the chocks.

Lastly, you will need to make sure the chocks are placed in the correct location – typically on either side or both sides of the wheels. With these items on hand and proper placement, you can ensure the safety and stability of your vehicle when parked or positioned on an incline.

A Level Surface

To achieve an A-level surface, you will need a few essential tools. The most crucial tool you’ll need is a high-quality levelling compound that will smoothen out any rough surfaces. A self-levelling compound is ideal since it can spread itself to create an even surface without much effort.

You’ll also need a trowel to spread the compound evenly, a primer to enhance the bonding of the compound to the surface, and a bucket for mixing the compound. Additionally, you’ll need a spirit level to ensure that your surface is levelled uniformly. Finally, consider getting gloves and protective gear to ensure that you’re safe while working.

With these simple tools, you can create a smooth and even surface that is perfect for any application.

Step-by-Step Guide

Putting a car on 4 jack stands may seem like a daunting task, especially if you’re not very familiar with working under a car. However, with the right tools and a bit of patience, it’s a job that can be easily accomplished. To start, ensure you have four jack stands that are rated to hold the weight of your car, and a hydraulic floor jack to lift the vehicle.

Park your car on a level surface and engage the emergency brake. Then, use the floor jack to lift one side of the vehicle at the designated lift point, and place one jack stand under it. Repeat this process on the other side of the car, placing another jack stand under the designated lift point.

Then, carefully lower the car onto both jack stands, making sure they are securely in place and not wobbling. Repeat the process on the front and rear of the vehicle, ensuring all four jack stands are evenly placed. Once the car is fully supported by the jack stands, it’s safe to work underneath it.

Always double check that the car is stable and secure before beginning any work, and never rely on just a jack to support the weight of the vehicle. With these simple steps, you can confidently put your car on 4 jack stands and easily perform any necessary repairs or maintenance.

Step 1: Park Your Car on a Level Surface and Chock the Wheels

When it comes to maintaining your car, there are some things that you can easily do yourself, such as changing the oil or replacing a flat tire. However, there are some tasks that require a bit more know-how, such as checking and changing your brake pads. In order to safely and effectively do this task, it is important to follow a step-by-step guide.

The first step in this guide is to park your car on a level surface and chock the wheels. This ensures that your car won’t move or roll while you are working on it. Chocking the wheels basically means using blocks or wedges to prevent the wheels from moving.

This can be done with any type of block or wedge, such as bricks, pieces of wood, or specially-made chocks. By taking this first step, you ensure that your car is secure and stable while you work on checking your brake pads.

Step 2: Locate the Proper Jack Points Under Your Vehicle

Locating the proper jack points of your vehicle is crucial to ensure the safety of your car and yourself during a repair or maintenance task. As a car owner, it’s essential to understand where these points are located. Typically, the jack points for a vehicle are indicated in the owner’s manual or stamped on the car’s metal frame.

However, if this information is not available, then a quick Google search or a visit to a mechanic can help you locate them. Once you’ve determined the jack point, ensure that the jack stands are correctly positioned and secure before lifting your vehicle. It’s also worth noting that it’s best to avoid makeshift jack points, such as suspension components or body panels, as they could lead to costly damage to your car.

By locating the appropriate jacking points and taking extra precautions, you can go ahead and perform repairs or modifications on your vehicle safely and confidently.

Step 3: Raise One Side of the Car with Your Jack and Place a Jack Stand Underneath

Once you’ve positioned your jack in the proper location, it’s time to start lifting up one side of the car. This can be a bit tricky, so make sure you have a good grip on the handle and that the jack is secure in its position. Begin pumping the jack up and down until you see the car start to rise.

Slow and steady wins the race here – don’t try to rush the process. Once you’ve raised the car to your desired height, it’s time to place the jack stand underneath. This is crucial for your safety, as relying solely on the jack can be dangerous.

The last thing you want is for the car to come crashing down on you while you’re working! So take your time and position the jack stand in a sturdy location – usually directly underneath the jacking point. Once it’s in place, lower the jack carefully onto the stand and double check to make sure it’s secure before you start working. Remember, safety first when it comes to DIY car repairs!

Step 4: Repeat Step 3 for the Other Side of the Car

After completing the previous step of thoroughly cleaning and drying one side of your car, it’s time to move to the other side and repeat the process. Start by gathering your tools and supplies again and positioning yourself on the other side of your car. Give your car a quick once-over to identify any areas that may need extra attention, such as the wheels or crevices.

Begin by washing the car with the soap and water mixture, using a sponge or soft-bristled brush to scrub away dirt and grime. Rinse thoroughly with clean water and dry the area with a microfiber towel, making sure to remove all excess water droplets. Proceed to the remaining sections of the car, making sure to reach all the nooks and crannies.

Finally, give your wheels and tires a thorough cleaning, using a separate sponge or brush and a dedicated wheel cleaner. By repeating this process on the other side of your car, you’ll ensure that every inch of your vehicle is sparkling clean and ready to hit the road.

Step 5: Raise the Rear of the Car with Your Jack and Place Jack Stands Underneath

Raising the rear of your car is necessary for performing several maintenance tasks, such as changing the oil, replacing brakes, or inspecting the suspension and exhaust system. To do so, you’ll need a floor jack and a pair of jack stands, which should have a weight capacity higher than your vehicle’s gross weight. To start, find the recommended jacking points in your car’s manual and position the floor jack in front of the rear wheels.

Pump the handle until the jack reaches the lifting point, then stop. It’s crucial to align the groove on the jack head with the pinch weld on the vehicle’s body, or you risk damaging the car’s frame. Once the jack holds the car steady, you can lift it a few inches higher, place the jack stands under the designated spots, and lower the car onto them.

Make sure the stands are level and secure before releasing the hydraulic pressure and removing the jack. A good rule of thumb is to wiggle the car gently, and if the jack stands don’t move, you’re good to go. With the car raised evenly and safely, you’re ready to tackle your maintenance task and keep your ride in top condition.

Step 6: Lower the Jack and Ensure That the Car is Level

Now that you’ve successfully changed your car’s tire, it’s important to lower the jack and ensure that your car is level before driving off. This step is crucial to prevent any mishaps after replacing the tire. Begin by slowly lowering the jack until the tire touches the ground.

Once you’ve confirmed that the car is securely on the ground, use a tire wrench to tighten the lug nuts in a star pattern to ensure even tightening. Once all the nuts are tightened, ensure that the lug nuts are properly secured by giving them a final check. Remember to stow away all your tools and the flat tire in the trunk.

It’s essential to drive slowly for the first few miles to ensure that the replacement tire has been installed correctly and doesn’t wobble. With this, you’re good to go!

Safety Tips

If you’re planning on doing some work under your car, it’s crucial to follow safety precautions to prevent accidents. One essential safety tip is to put your car on four jack stands to ensure stability. To do this, you’ll need to start by finding a flat surface, then slide your jack under the car and raise it up.

Once you’ve lifted the car, place the first jack stand under one of the car’s main supporting points, such as the front or rear suspension. Repeat this step for the other sides of the car. Once you’ve secured all the jack stands, gently give the car a shake to ensure it’s stable before getting to work.

Remember that using jack stands is critical to your safety when doing work on your car, and you should never rely only on a car jack to hold your vehicle in place. By following these safety tips, you’ll be able to get your car up on four jack stands while ensuring that you maintain a safe environment.

Never Work Under a Car Without Proper Support

As someone who has worked on cars in my spare time, I can’t stress enough how important it is to use proper support when working under a car. Whether you’re changing the oil or fixing a broken part, it’s important to use a jack stand or a ramp to support the weight of the vehicle. Jacks alone are not enough, as they can slip or fail over time.

Using a proper support mechanism can prevent serious injury or even death. Ensure that you have the right support equipment before starting any automotive work. Remember, safety is always the number one priority when working on any type of machinery, including cars.

So invest in a quality set of support equipment and use it every time you work on your vehicle. Your life could depend on it.

Always Use Jack Stands on a Level Surface

Using jack stands when working on your vehicle is crucial for safety, but it’s important to make sure you’re doing it right. Always use jack stands on a level surface to prevent accidents and ensure stability. Uneven or soft ground can cause the jack stands to shift or tip over, putting you at risk of injury.

When choosing a surface, look for a flat and sturdy area, such as a concrete driveway or garage floor. It’s also a good idea to check the weight capacity of your jack stands to ensure they can safely hold the weight of your vehicle. Remember, safety should always come first when working on your car, and using jack stands on a level surface is just one way to ensure you’re doing everything correctly.

Double Check Your Work Before Getting Under the Car

Getting under the car can be a risky business if you haven’t double-checked your work first. One of the most important things you can do to ensure safety is to check your brakes and suspension before getting under the car. These are critical systems that can fail without warning, which could lead to serious injuries or even death.

Another important safety tip is to make sure that the car is securely supported before getting under it. This means using jack stands or blocks to hold the car up, rather than relying on a hydraulic jack alone. You should also wear appropriate safety gear, including gloves, eye protection, and sturdy shoes with non-slip soles.

Remember, a little bit of extra time spent double-checking your work and taking necessary safety precautions can go a long way in preventing accidents and injuries. Stay safe out there!


In conclusion, putting a car on 4 jack stands may seem like a daunting task, but with the right tools and a little bit of know-how, it can be accomplished easily and safely. Remember to always double-check your work and never compromise on safety. And if all else fails, just call a professional- after all, they have a knack for lifting spirits (and cars) to new heights!”


What materials do I need to put a car on 4 jack stands?
To put a car on 4 jack stands, you will need the following materials: 4 jack stands, a hydraulic jack, wheel chocks, and a flat surface.

Can I put a car on 4 jack stands without a hydraulic jack?
No, a hydraulic jack is necessary to lift the car high enough to place the jack stands at the correct height.

How high should I place the jack stands?
The jack stands should be placed at a height that allows them to securely support the weight of the car. Refer to your car’s owner’s manual for the correct height placement.

Is it safe to put a car on 4 jack stands?
Yes, it is safe to put a car on 4 jack stands as long as they are placed correctly and securely on a flat surface. Always use caution when lifting and lowering the car.

How do I ensure the car is stable on the jack stands?
After placing the car on the jack stands, shake the car slightly to ensure it is stable. If the car wobbles or shifts, readjust the jack stands and try again.

Can I work on the car while it is on 4 jack stands?
Yes, you can work on the car while it is on 4 jack stands, but use caution as the car is elevated. Do not crawl under the car or place body parts underneath it.

How do I lower the car from the 4 jack stands?
To lower the car, use the hydraulic jack to lift the car slightly and remove the jack stands one at a time, lowering the car until it is securely on the ground.

Show More

Related Articles